Cascade Mihpt
  • Site Characterization

What is an MIHPT?

May 5, 2020 -

Selecting the right tool is the first hurdle when incorporating high resolution site characterization into your site management strategy. To design the most effective strategy, a project manager needs to know the purpose and objectives of the site investigation and the types of data each site characterization tool provides.  This blog provides a quick rundown on what the Membrane Interface Probe – Hydraulic Profiling Tool (MIHPT) can do and where it provides the most value in your site characterization tool kit.

As the name suggests, the MIHPT is a combination of other tools developed separately. Brought together, these multiple data streams create a robust collaborative data set project managers rely upon for strategic site management decisions. The tool combines a Membrane Interface Probe (MIP), Hydraulic Profiling Tool (HPT), and a diode capable of measuring electrical conductivity (EC). The tool itself is advanced into the subsurface via direct push drilling technology. So, if you can get a probe to your target depth, you can get an MIHPT there too.

MIHPT probe

Figure 1: An MIHPT probe and trunkline. Source: Geoprobe

Membrane Interface Probe

The MIP portion of the system provides a continuous vertical log of the relative level of impact of volatile organic compounds. This is a screening-level tool providing semi-quantitative data. It operates by moving a stream of carrier gas (nitrogen) down to the probe tip and looping back up to ground surface. The gas passes by a semi-permeable membrane at the bottom of the loop. A heater block below the membrane heats up the subsurface before the membrane passes by. If there are volatile organic compounds (VOCs) present, they will volatilize and pass through the membrane and into the carrier gas, which then brings them back to a set of detectors at the surface. The measurements from these detectors are presented in real time and charted against the depth below ground surface. There are four detectors on most MIHPT units:

 

Photoionization Detector (PID) – This is the tool with which most project managers are familiar. It is essentially the same PID technology everyone brings on site in a handheld unit to screen soil samples and ambient air. Accordingly, it is subject to many of the same limitations. It detects all VOCs, both petroleum hydrocarbons and chlorinated solvents.

Flame Ionization Detector (FID) – Here’s another familiar tool that’s usually found in a handheld unit. The FID detects combustible volatiles and is more useful for characterizing sites with petroleum hydrocarbon impacts.

Electron Capture Detector (ECD)– This instrument detects halogenated compounds, the family that includes chlorinated solvents. The ECD is much more sensitive than the XSD (described below) and is preferentially more sensitive to more highly chlorinated compounds such as PCE and TCE.

Halogen-Specific Detector (XSD) – This detector is only able to detect halogenated compounds. It is less sensitive than the ECD and does not exhibit the same bias toward highly chlorinated compounds. Running both the ECD and the XSD together provides great value since the ECD can detect lower concentrations and if it gets saturated by a high concentration, the XSD is there to back it up.

 

Hydraulic Profiling Tool

The HPT creates a real time log of the relative formation permeability versus depth as the probe is advanced into the subsurface. It operates by injecting clean water from an aboveground reservoir at a constant flow rate through the direct push rods and out into the surrounding soil via an injection port on the side of the probe. Simultaneously, sensors record the flow rate, the back pressure required by the pump to maintain that flow rate, and the current depth of the probe. These measurements are collected by the onboard software. An estimated hydraulic conductivity (K) value is calculated and plotted alongside the other measurements in real time.

Generalized Schematic of the HPT tool

Figure 2: Generalized schematic of the HPT tool. Source: Geoprobe HPT Standard Operating Procedure

The final piece of the MIHPT is the electrical conductivity (EC) probe. In a general sense, the electrical conductivity of a soil varies with grain size. This correlation is utilized to better understand subsurface conditions based on the EC data. The EC measured in the subsurface varies based on changes in mineralogy, groundwater geochemistry, and contamination. It is important, then, to confirm the accuracy of the EC data for this use by collecting confirmatory soil borings from your site.

 

relationship between electrical conductivity and grain size

Figure 3: Relationship between electrical conductivity and grain size. Source: Geoprobe Electrical Conductivity System Standard Operating Procedure

Bringing it all Together

Combining this continuously logged information about geology, hydrogeology, and contaminant type & distribution into a single subsurface advancement is extremely valuable. In a matter of minutes or hours, you can generate more detailed and comprehensive data than traditional sampling means collect in weeks.

Ready to learn more?  Join me on May 13, 2020 for my Leveraging MIHPT Data for Optimized In Situ Remediation Approach webinar when my colleague Eliot Cooper and I explain in detail how to use this tool – from selection to program design, and then on to data interpretation using Cascade’s “Expert Rules.” The Cascade team has characterized and remediated thousands of sites. We’ve seen these MIHPT data sets put to the test when it comes time spent designing remediation programs. Based on that experience, our Expert Rules streamline your confirmation sampling and remediation design programs.  

 

ABOUT THE AUTHOR

Jason Flattery

Jason Flattery, PE

DIRECTOR OF OPERATIONS, SITE CHARACTERIZATION

jflattery@cascade-env.com

 

Jason Flattery is the Director of Operations, Site Characterization at Cascade Environmental.   Jason has two decades of experience in environmental services industry and is a national expert on high resolution site characterization (HRSC) tools and strategies. He has extensive experience designing and implementing injection remedies, managing large-scale construction projects, and developing HRSC programs. He is a critical resource for clients who need their HRSC efforts to provide clear and positive impact on their timelines, project costs and remediation efficacy and optimization.

Jason holds a BS in Civil & Environmental Engineering, an MBA, and is a registered professional engineer in Massachusetts.


comments powered by Disqus

Categories

Thank you for subscribing to Cascade's newsletter.
THANK YOU FOR SUBSCRIBING TO CASCADE'S NEWSLETTER.